![]() ![]() Reconnect the car battery (starting with the positive terminal this time), and you should be done.Fill the power steering fluid reservoir (PS fluid reservoir.).Then, reinstall the serpentine belt (or drive belt), the radiator fan, and shroud.Reattach each pressure line to the new power steering pump.Secure the new pump to the engine block by screwing each bolt through the mounting bracket and onto the engine block.Then, replace the power steering belt and ensure your belt tension is correct.Install the new PS pump and replace the power steering pulley so that it’s aligned with the crankshaft pulley.Then secure it to the bracket using the old mounting bolts. First, transfer the mounting bracket from the old pump body to the new one.This is how to install a new power steering pump: The power steering pump body can now be removed.You can do this using an impact wrench or a socket. Remove the mounting bolts which hold the power steering pump onto the engine block. ![]() Using a power steering removal tool, detach the power steering pump pulley by removing the locking nut.This includes each pressure line from the power steering reservoir as well as the return hose and hose clamp from the gearbox. Once the primary supply line is removed, you can remove all other lines from the power steering pump.Using a socket or ratchet, remove the hydraulic lines that are connected to the bottom of the power steering pump.Then, place a drip tray under your vehicle as there may be a power steering fluid leak (PS fluid leak).First, locate the lines going to your power steering pump.Here’s how to disconnect the power steering pump itself: Finally, remove the radiator fan shroud and the fan to gain clear access to the power steering pump.The Power Steering Fluid Reservoir Is Located Toward The Rear Of The. Then, remove the lower engine covers (skid plate.) Chevrolet Equinox 2014 Manual Online: power steering fluid, L4 Engine), V6 Engine).To remove the serpentine belt, loosen the tensioner pulley located on the left side (as you look at the engine.) Once loose, you can easily slip off the belt. 16 Equinox LTZ AWD 3.6 -23 Silverado LTZ 6.2-20 Traverse High. Detach the serpentine belt or drive belt. Does anyone know how much power steering fluid (capacity) a 2016 3.6 V6 terrain holds.Open the hood and remove your engine cover.Using a hydraulic lift or a jack, lift up your vehicle onto jack stands.Before anything else, disconnect your battery (starting with the negative terminal.).You need to access your power steering pump first: These systems use an electric motor instead of a hydraulic system and therefore do not have any power steering fluid to leak. FlexFuel Our research indicates that your vehicle has an electric power steering system ('EPS' or 'EPAS'). With that said, here’s how to perform a power steering pump replacement: 1. FlexFuel Check Power Steering Level: 2012 Chevrolet Equinox LT 2.4L 4 Cyl. However, if you’re not familiar with auto parts, it’s best to let a professional mechanic handle the repair job to avoid hurting yourself or doing any more damage to your car. If your steering is hard, look at the 80 amp fuse in the engine compartment fuse. Refer toPower Steering System Bleeding.Clean any excess power steering fluid from the vehicle.A power steering pump replacement (PS pump replacement) can be done as a DIY job at home. The Equinox doesnt have a power steering pump, It has a power steering motor. To find the ideal power steering fluid for your car in the owner’s manual, click here. Since a few years ago, however, manufacturers use fluids that are specific for each car. Refer toPower Steering Fluid Reservoir Replacement - Lower.Fill and bleed the power steering system. In short: The power steering fluid is usually the ATF type, and we can identify it by its red color. Refer toPower Steering Pump Pulley Replacement.Transfer the lower power steering fluid reservoir. Our research indicates that your vehicle has an electric power steering system ('EPS' or 'EPAS'). Power Steering PumpProcedureRemove the power steering pump through the right front wheel well opening.Transfer the power steering pump pulley. Refer toPower Steering Gear Inlet Pipe/Hose Replacement. Power Steering Fluid Reservoir Outlet Hoseĭisconnect the power steering fluid reservoir outlet hose from the lower power steeringfluid reservoir.ĭisconnect the power steering fluid cooling pipe from the lower power steering fluidreservoir.ĭisconnect the power steering gear inlet hose from the power steering pump. Refer toTire and Wheel Removal and Installation.Remove the drive belt from the power steering pump pulley only. Refer toIntake Manifold Cover Replacement.Remove as much power steering fluid from the upper power steering fluid reservoiras possible.Remove the right front tire and wheel assembly. Preliminary ProceduresPlace drain pans under the vehicle.Remove the intake manifold cover. Chevrolet Equinox Service Manual / Chassis / Steering / Power Steering Pump Replacement Hydraulic Steering Steering Pump ![]()
0 Comments
Leave a Reply. |